Watlow Series SD PID Profiling Controller Uživatelský manuál Strana 50
- Strana / 88
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Watlow Series SD • 48 • Chapter 10 Profiling
Display Parameter name
Description
Set-
tings
Range
(Integer values for Mod-
bus in parentheses.)
Default Modbus*
(less 40,001
offset)
Read/Write
Appears if:
[StYp] Set Point Step
[tg;SP]
[tg.SP]
Target Set Point
Indicates ending set point value the
controller ramps to during the set
point step.
-1999 to 9999
(-1999000 to
9999000)
Target set point values
must be between
[SP;Lo] to [SP;Hi] or
step will fail the Pre-
Run check and will
not run.
75 See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
[hour]
[hour]
Hours
The number of hours, (plus Min and
Sec parameters) equal the total step
time to achieve the ending set point
under the [styp] step type.
0 to 99 0 See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
Active if the value
set for [ptyp] is
[``ti] or time
based profiles.
[Min]
[ Min]
Minutes
The number of minutes, (plus Hour
and Sec parameters) equal the total
step time to achieve the ending set
point under the [styp] step type.
0 to 59 0 See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
Active if the value
set for [ptyp] is
[``ti] or time
based profiles.
[`SEc]
[ SEc]
Seconds
The number of seconds, (plus Hour
and Min parameters) equal the total
step time to achieve the ending set
point under the
[styp]
step type.
0 to 59 0 See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
Active if the value
set for [ptyp] is
[``ti] or time
based profiles.
[rAte]
[rAtE]
Rate
Indicates rate at which the set point
changes in degrees per minute.
0 to 9999 100 See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
Active if the value
set for [ptyp] is
[rate] or rate
based profiles.
[Ent1]
[Ent1]
Event Output 1
Selects whether Event Output 1 is
on or off during the program step.
[`Off] (0)
[``On] (1)
[`Off] (0)
See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
Output 1 is set to
[Ent1].
[Ent2]
[Ent2]
Event Output 2
Selects whether Event Output 2 is
on or off during the program step.
[`Off] (0)
[``On] (1)
[`Off] (0)
See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
Output 2 is set to
[Ent2].
[Ent3]
[Ent3]
Event Output 3
Selects whether Event Output 3 is
on or off during the program step.
[`Off] (0)
[``On] (1)
[`Off] (0)
See page 53. Profiling version only.
(SD_ R - _ _ _ _ - _
_ _ _ )
Output 3 is set to
[Ent3].
Note: Some values will be rounded off to fit in the four-character display. Full values can be read with Modbus. All temperature
parameters are in °F through Modbus.
* Low register numbers contain the two higher bytes; high register numbers contain the two lower bytes of the four-byte integer.
Decimal precision is implied at three decimal places unless otherwise noted.
- User’s Manual 1
- Series SD 1
- PID Controller and 1
- PID Profiling Controller 1
- Safety Information 2
- Technical Assistance 2
- Warranty 2
- Table of Contents 3
- Chapter 1: Overview 4
- Features and Benefits 5
- Dimensions 6
- Panel Cutout 7
- Installation 8
- Wiring the Series SD 13
- Thermocouple Input 14
- 0 to 10VÎ (dc) Process Input 14
- Output 1 Solid-state Relay 15
- 0 to 20 mA Process Input 15
- Output 1 Mechanical Relay 15
- Output 1 Switched DC 16
- Output 1 Process 16
- Output 2 Mechanical Relay 16
- Output 2 Solid-state Relay 17
- Output 2 Switched DC 17
- Output 2 EIA/TIA-485 17
- Output 3 Mechanical Relay 18
- Output 3 Solid-state Relay 18
- Output 3 Switched DC 18
- Output 3 Open Collector 19
- Output 3 Process 19
- 12V (dc) 20
- Ethernet Gateway 21
- (static set point 22
- (profiling 22
- Home Page Overview 23
- Operations Page Overview 24
- Setup Page Overview 25
- Programming Page Overview 26
- Factory Page Overview 26
- Read/Write 27
- Chapter 6: 38
- Chapter 7: 42
- Chapter 8: Programming Page 45
- Programming Page Example 46
- Chapter 9: Programming Page 47
- The Profiling Menu 49
- Set Point Step 50
- [SoaH] Soak Step 51
- [``JL] Jump Loop Step 52
- [LFiL] Link File Step 52
- [~End] End Step 52
- Pre-Run Menu** 53
- Run Menu* 53
- Step Types 54
- Set Point 55
- Guaranteed Soak 55
- Deviation Window 55
- Example profile 56
- Chapter 11: Factory Page 61
- Chapter 12: Features 63
- Operations Page 64
- Temperature 65
- Calibration Offset 66
- Filter Time Constant 67
- Sensor Selection 67
- Access Lockout 67
- Control Methods 68
- Single Set Point Ramping 72
- Alarm Set Points 72
- Retransmit 73
- Communications 73
- Setting Up a Modbus Network 74
- • 73 • Chapter 12 Features 75
- Troubleshooting 76
- Error Messages 78
- Specifications 79
- ____ ____ 81
- Prompt Index 82
- Declaration of Conformity 87
- How to Reach Us 88
Související produkty a manuály pro Senzory Watlow Series SD PID Profiling Controller
(80 stránky)
(80 stránky)
Senzory Watlow Series PD Uživatelský manuál
(188 stránky)
(188 stránky)
Senzory Watlow Series V4 Uživatelský manuál
(21 stránky)
(21 stránky)
Senzory Watlow Silver Series EM Uživatelský manuál
(18 stránky)
(18 stránky)
Senzory Watlow Silver Series OIT Uživatelský manuál
(14 stránky)
(14 stránky)
Senzory Watlow Series V4T Uživatelský manuál
(26 stránky)
(26 stránky)
Senzory Watlow TLM-8 Uživatelský manuál
(8 stránky)
(8 stránky)
Senzory Watlow WATVIEW Uživatelský manuál
(36 stránky)
(36 stránky)
Senzory Watlow Serie 96 Uživatelský manuál
(92 stránky)
(92 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce